USPTO serial 74510042
Reviewed by CopyMark Law Group
These status codes mean the trademark application is abandoned and no longer pending. Common reasons include missing an Office Action response (600), filing without a valid basis (602), express abandonment by the applicant (604), or failure to respond to an examiner's inquiry (618). Revival may be possible in limited circumstances. If abandonment was unintentional, consult counsel about a petition to revive. Otherwise file a new application if protection is still needed.
If you own this trademark, we can monitor new filings and help with USPTO deadlines. If you do not, we can file a new U.S. application.
The USPTO lists this attorney as the applicant's representative for correspondence on this application.
Roxanne Eades
ROXANNE EADES FELSMAN, BRADLEY, GUNTER & DILLON, LLP2600 CONTINENTAL PLZ777 MAIN STFT WORTH, TX 76102| Class | Description | Status | First use |
|---|---|---|---|
| 007 | aftermarket parts for motorcycle engines, namely electronic ignitions, chokes, carburetors, choke cables, exhausts, pistons, spark plugs, spark coils and generators, advance units comprised of advance weights, advance springs, ignition parts for internal combustion engines, namely points and condensers, point plates, point cams, timer screws and timing wires, exhaust pipes, mufflers, kick starters, intake manifolds, engine blocks, oil coolers, rocker arms, oil lines, push rods, engine valves, engine cylinders, heads, cam cases, oil pumps, and manifold clamps | ABANDONED | Aug 15, 1994 |
| 008 | hand tools manufactured for motorcycles, namely engine stands, motorcycle lifts, transmission stands, static timing tools, crank case pullers, oil seal pullers, outer race press plugs, pinion gear puller, rod race driver for removing and installing rod races, sprocket nut wrench and sprocket shaft bearing driver, cam cover pullers, cam pinion press plugs, valve spring compressors, valve guide driver sets, namely intake sockets, exhaust sockets and driver handles, motorcycle lifts and lift dollies, tappet guide pullers, piston pin bushing removal tools, tappet screen/roller removal tools, trap door pullers, transmission removal/ installation tools, namely wrenches and sockets, primary plug sockets, clutch hub tools, namely washers, pullers, studs and pins, clutch spring compressors, tire irons, lug wrenches, wheel bearing drivers, wheel bearing greasers, spoke wrenches, chain breakers and shock spanner wrenches | ABANDONED | Aug 15, 1994 |
| 009 | aftermarket parts for motorcycles, namely speedometers, tachometers, odometers, speedometer gauges, tachometer gauges, oil pressure gauges, oil temperature gauges, amp meter gauges, fuel gauges, batteries, voltage regulators, turn signals, switches, electric relays | ABANDONED | Aug 15, 1994 |
| 011 | aftermarkt parts for motorcycles, namely lights | ABANDONED | Aug 15, 1994 |
| 012 | aftermarket parts for motorcycles, namely handle bar clamps, frame clamps, light clamps, fender clamps, footrest clamps, fuel line clamps, gauge clamps, mirror clamps, wheels, tires, hubs and rims, shock absorbers, windshields, footrests, handle bars, luggage racks, gear shifts, seats, backrests, pedals, rear view mirrors, handle bar grips, clutch grips, brake shifter grips, handle bar levers, clutch levers, brake shifter levers, wire cables, namely clutch cables, speedometer cables, tachometer cables, and brake and throttle cables, grills, fenders, clutches, brakes, calipers, master cylinders, brake linings, kickstands, frames, front forks, triple trees, namely for front fork brackets, horns, fenders, connecting rods, fan and drive belts, transmissions, sprockets, primary drive belts, primary drive gears, axles, filters, namely oil, gas, air and crankcase vent filters, primary and secondary drive chains, air cleaners, wheel bearings, transmissions, gas tanks, oil tanks, instrument display panels, motor mounts, nonmetal brake hoses, nonmetal oil line hoses, nonmetal fuel hoses, metal brake hoses, metal oil line hoses, and metal fuel hoses, handle bar brake controls, hydraulic and mechanical handle bar clutch controls, mechanical and hydraulic handle bar shift controls, mechanical and hydraulic foot shift controls, mechanical and hydraulic foot brake controls, and mechanical and hydraulic hand shift controls | ABANDONED | Aug 15, 1994 |
| 022 | after market parts for motorcycles, namely tie down straps | ABANDONED | Aug 15, 1994 |
CopyMark links this record to cited §2(d) serials, the owner's other marks, Nice classes, similar mark names, and recently changed USPTO applications.
| Date | Code | Event | What it means |
|---|---|---|---|
| May 29, 1996 | ABN2 | ABANDONMENT - FAILURE TO RESPOND OR LATE RESPONSE | The trademark application was abandoned because a required response or document was not filed by the deadline — usually a missed Office Action response. The application is dead unless a petition to revive is granted within a limited time. |
| Aug 31, 1995 | CNRT | NON-FINAL ACTION MAILED | A non-final Office Action means the USPTO examining attorney has raised at least one issue with your trademark application but has not made a final decision. You usually have three months to respond with arguments, amendments, or evidence. Missing the deadline can abandon the application. |
| Jul 28, 1995 | CRFA | CORRESPONDENCE RECEIVED IN LAW OFFICE | — |
| May 18, 1995 | CNRT | NON-FINAL ACTION MAILED | A non-final Office Action means the USPTO examining attorney has raised at least one issue with your trademark application but has not made a final decision. You usually have three months to respond with arguments, amendments, or evidence. Missing the deadline can abandon the application. |
| May 8, 1995 | AUPC | AMENDMENT TO USE PROCESSING COMPLETE | — |
| Mar 2, 1995 | CRFA | CORRESPONDENCE RECEIVED IN LAW OFFICE | — |
| Mar 2, 1995 | IUAF | USE AMENDMENT FILED | — |
| Sep 19, 1994 | CNRT | NON-FINAL ACTION MAILED | A non-final Office Action means the USPTO examining attorney has raised at least one issue with your trademark application but has not made a final decision. You usually have three months to respond with arguments, amendments, or evidence. Missing the deadline can abandon the application. |
| Sep 14, 1994 | DOCK | ASSIGNED TO EXAMINER | — |
| Aug 31, 1994 | DOCK | ASSIGNED TO EXAMINER | — |